Here below you will discover some dependable data about Installing A Bathtub.
Mounting a tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a new one is additionally a moderately tough project. If the old tub is conveniently available, the task can move rapidly; if you need to open a wall surface to get rid of the old tub as well as place the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also set in the new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. As opposed to working with a professional to take control of a halfway-completed task, it is better to consider utilizing one prior to you start. Chances are you may need a specialist plumber to make tube links.
This article will assist you set up a brand-new bath tub in your bathroom if you have actually already bought a new tub and don't need to change the arrangement of your previous supply of water pipes.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be fairly troublesome due to the limited accessibility that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. When the supply pipes have been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Before moving on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will need a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin ensuring that the washing machines are in area between the faucet and the sink. Safeguard the tap in position with the producer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind should be linked to the tap ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Making use of the two wooden boards under its feet, put the bathtub in the called for placement. The wooden boards are useful in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny factors.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level and also readjusting the feet on the tub until the level checks out degree.
To set up taps, fit all-time low of the furthest flexible faucet connector to the ideal supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the supply of water and inspect all joints and brand-new pipework for leaks and also tighten them if required. Fill the tub and likewise check the overflow electrical outlet and the regular outlet for leakages.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub must wait until the tub has been utilized at least once as this will certainly settle it into its last position.
Getting ready for the Installment
Firstly, the supporting framework provided with the bath ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its last setting.
Tiling Around the Tub
In the area where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split an inflexible seal, triggering the water to permeate the wall between the bath and the tiling, bring about problems with moisture and possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can split fairly very early if you do not take into consideration this activity prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were guided to that write-up about Tools You Need to Install a New Bathtub from a good friend on our other web page. Are you aware of somebody else who is involved in A Step-by-Step Guide to Installing a Bathtub? Why not promote it. We appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Recurring Service Plans